English
FrançaisNon-tariff Measures
Showing items 3101 to 3120 of 7642
-
Applied by Zambia on the entire world
The measure came into effect on 03 February 1996
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 03 February 1996
- Publication where the measure is specified
- THE AGRICULTURE (FERTILISERS AND FEED) ACT
- Regulation where the measure is specified
- THE AGRICULTURE (FERTILISERS) REGULATIONS
- Country/Region applying the measure
- Zambia
- The rationale of the measure
- Not specified
- Coded list of objectives
- A: Protection of human life and health and B: Protection of life and health of animals
- Description of the measure
- Any person who shall, without lawful authority, alter or deface any note, docket or mark placed upon any package or container under this Act or under any order, requirement, condition or regulation made thereunder; or who shall remove any such note, docket or mark from any such package or container upon which it is required to be kept or attached under this Act or under any order, requirement, condition or regulation made thereunder ; shall be guilty of an offence.
- Reference of the measure
- Section 46 (b)
- Measure also domestic
- Yes
Products affected by the measure.
- Description
- Fertiliser and farming requisites
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zambia on the entire world for
The measure came into effect on 18 July 2003
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 18 July 2003
- Publication where the measure is specified
- Statutory Instrument No. 78 of 2003
- Regulation where the measure is specified
- ZS 263 1990 Specification for hair oils
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- Prescribes requirements for hair oils based cosmetic preparation for the hair.
Covers quality requirements, sampling, testing, packing and marking - Reference of the measure
- Page 369 of SI 78 of 2003
- Measure also domestic
- No
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out PG: 22 Cosmetics No - Description
- Hair oils
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zambia on the entire world
The measure came into effect on 18 July 2003
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 18 July 2003
- Publication where the measure is specified
- STATUTORY INSTRUMENT NO. 78 OF 2003
- Regulation where the measure is specified
- ZS 432 Part 1: 2002 Safety for Incandescent Lamps - Specification Part 1:Tungsten filament lamps for domestic and similar general lighting purposes.
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- Tungsten halogen lamps for domestic and similar general lighting purposes.
Covers quality and marking requirements - Reference of the measure
- Page 369 of SI 78 of 2003
- Measure also domestic
- No
Products affected by the measure.
- Description
- Tungsten halogen lamps for domestic and similar general lighting purposes.
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zambia on the entire world
The measure came into effect on 18 July 2003
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 18 July 2003
- Publication where the measure is specified
- Statutory Instrument No. 78 of 2003
- Regulation where the measure is specified
- ZS 119: Industrial safety belts and harnesses
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- Specifies the minimum performance criteria and requirements for the manufacture and use of safety belts, harnesses and lanyards.
Covers quality requirements, performance test, marking and storage - Measure also domestic
- No
Products affected by the measure.
- Description
- Safety belts, harnesses and lanyards.
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zambia on the entire world for
The measure came into effect on 18 July 2003
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 18 July 2003
- Publication where the measure is specified
- Statutory Instrument No. 78 of 2003
- Regulation where the measure is specified
- ZS 063 Petroleum Jelly -Specification
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- A: Protection of human life and health, B: Protection of life and health of animals and E: Protection of the environment
- Description of the measure
- Specifies requirements of petroleum jelly for the cosmetic industry
Also covers inspection, testing, sampling, marking, labelling and quality requirements - Measure also domestic
- No
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out PG: 22 Cosmetics No - Description
- Petroleum jelly for the cosmetic industry
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zambia on the entire world
The measure came into effect on 01 January 1970
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 01 January 1970
- Publication where the measure is specified
- The Firearms Act
- Regulation where the measure is specified
- Firearms Act 1970
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- G: Protection of national security
- Description of the measure
- 8. (1) All firearms and ammunition imported into Zambia for the purpose of sale shall be registered in the prescribed manner according to any existing numbers or marks on such firearms or parts thereof or on any package of ammunition, and, if so required by an authorised officer, shall be stamped or otherwise marked in the prescribed manner.
- Reference of the measure
- PART II : Section 8 (1)
- Measure also domestic
- No
Products affected by the measure.
- Description
- Firearms
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zambia on the entire world
The measure came into effect on 03 January 1977
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 03 January 1977
- Publication where the measure is specified
- The Control of Goods Act
- Regulation where the measure is specified
- THE CONTROL OF GOODS (IMPORTATION OF SOAP) ORDER
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 3 (5) The container or wrapper of abrasive soap which is imported for sale shall at the time of importation have prominently displayed thereon words indicating, as may be appropriate, that it is "abrasive soap", "abrasive soap powder" or "pumice soap", or that it contains abrasive matter or is intended to be used for scouring or polishing, and if no such container or wrapper is used then such words shall be clearly and legibly stamped or embossed on each tablet, cake or block, in which such soap is imported.
- Reference of the measure
- Ministerial Order No. 3 (5)
- Measure also domestic
- No
Products affected by the measure.
- Description
- Abrasive soap
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zambia on the entire world for 0405.10.00: - Butter
The measure came into effect on 01 December 1972
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 01 December 1972
- Publication where the measure is specified
- The Law of Zambia; Republic of Zambia
- Regulation where the measure is specified
- Food and Drugs Act
- Country/Region applying the measure
- Zambia
- The rationale of the measure
- To protect the public against health hazards and fraud in the sale and use of food
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 188.Butter shall be the fatty product derived exclusively from milk; may contain see Part III of the Nineteenth Schedule), permitted neutralizing salts for pH adjustment (see Part X of the Nineteenth Schedule) or harmless lactic acid producing bacterial cultures; and shall have not less than 80 per centum of milk fat, not more than 2.0 per centum of milk solids-not-fat, 3.0 per centum of salt and 16 per centum of water. When obtained wholly or partly from a milk origin other than a cow, butter shall be so designated along with such a word denoting the animal from which the milk has been derived.
- Reference of the measure
- Part II para 188
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 0405.10.00 - Butter No - Description
- Butter
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world 01 December 1972 - Description
- All countries
-
Applied by Zambia on the entire world for 8423: Weighing machinery (excluding balances of a sensitivity of 5 cg or better), including weight operated counting or checking machines; weighing machine weights of all kinds. and 9016.00.00: Balances of a sensitivity of 5 cg or better, with or without weights.
The measure came into effect on 20 February 1998
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 20 February 1998
- Publication where the measure is specified
- Supplement to the Republic of Zambia Government Gazette dated 20/02/1998. statutory Instrument No 22 of 1998,the weights and Measures Act
- Regulation where the measure is specified
- The weights and Measures (assize) regulations, 1998
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 22. (1) An automatic weighing instrument shall be—
(a) of a pattern brought into use after the thirtieth day of October,1964 and certified by the Superintendent Assizer under section fifteen of the Act;
(b) securely fixed in position in which it will operate;
(c) tested in situ with the produce it is intended to weigh;
(d) fitted with seals to protect all adjusting devices or have all such devices operable only with a special detachable key;
(e) marked with clear marks, of identification on all parts that require to be dismantled; for any purpose whatsoever but which marks give a clear indication of the parts which match on re-assemble;
(f) provided with suitable means of extracting from any hopper or conveyor such loads or sample deliveries as the assizer may require for the tests;
(g) tested by taking not less than twenty sample deliveries either at random or in sequence, which tests shall be repeated as many times as the assizer considers necessary; and
(h) marked with a stamp of assize upon a lead plug in a conspicuous place on the beam, main body or frame of the instrument.
(2) The limits of error allowed on an automatic weighing machine shall be 1 scale interval at a load below 2000 scale intervals and for load exceeding 2000 scale intervals, the limit of error at initial assizing shall be increased to 2 stale intervals - Reference of the measure
- Part IV section 22 (h)
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 8423 Weighing machinery (excluding balances of a sensitivity of 5 cg or better), including weight operated counting or checking machines; weighing machine weights of all kinds. Yes Automatic weighing instruments 9016.00.00 Balances of a sensitivity of 5 cg or better, with or without weights. No - Description
- Automatic weighing instruments
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world 20 February 1998 - Description
- All countries
-
Applied by Zambia on the entire world for 8423.8: - Other weighing machinery :
The measure came into effect on 20 February 1998
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 20 February 1998
- Publication where the measure is specified
- Supplement to the Republic of Zambia Government Gazette dated 20/02/1998. statutory Instrument No 22 of 1998,the weights and Measures Act
- Regulation where the measure is specified
- The weights and Measures (assize) regulations, 1998
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 27. (1) In a platform machine or weighbridge—
(a) the upper surface or edge of the steelyard shall be in a straight plane from the zero graduation to the nose, end;
(b) there shall be no readily removable parts other than the counter balance to support the counter poise weights;
(c) adequate stops shall be provided to prevent any poise from travelling behind the zero graduation;
(d) provided with a load carrying rail the rail shall be distant from any other rail not less than 10 mm: Provided that where the load carrying rails overlap or have abridging piece, a gap of 5 mm shall be maintained between the overlapping parts.
(2) A weighbridge shall have—
(a) provision for adequate drainage and the pit kept free from any accumulation of water, mud or debris;
(b) its approaches smooth, straight and level for a distance of not less than the length of the platform
at each end of the weighbridge;
(c) the building housing the chart or steelyard so constructed that the operator has a clear view and unobstructed view of the entire platform or platforms;
(d) the platform so protected as to allow vehicles to pass on and off the platforms at both ends only;
(e) foundations of adequate strength to support, without change of position, both the mechanism and a load equal to the capacity of the weighbridge; and
(f) provision for adequate re-enforcement in any concrete work to resist any point loading in any direction to the satisfaction of a competent civil engineer.
(3) Where a platform machine or weighbridge is not provided with a tare beam the weight of any loose receptacle of frame used in conjunction with the instrument shall be accurately compensated for by means of a counter poise weight distinctive in shape from any of the ordinary counter poise weights
belonging to the instrument and such compensating weight shall have words " TARE WEIGHT"legibly and conspicuously stamped on its edge.
(4) The range of balance—
(a)in a platform machine, shall not exceed one-half percent of the capacity of the machine and shall be not less than one-eighthper cent of such capacity each way from the centre of travel of the ball; or
(b) in a weighbridge shall be double the range permitted in a platform machine.
(5) The travel of the steel yard each way from the horizontal position shall not be less than 10mm in both platform machine and weighbridge.
(6) A platform machine and a weighbridge shall be tested for accuracy in accordance with regulation 18 and also perform additional tests as required for electronic scales.
(7) The maximum permissible errors allowed shall be as indicated in Table 3 as read with Tables 5 and 6 of the First Schedule and errors in service shall be twice those applied on initial verification.
(8) The stamp of assizer shall be stamped upon a lead plug inserted in a conspicuous and easily accessible position on the instruments and the official date stamp shall be stamped upon the lead plug in the adjusting hole of any counter poise or tare weight.
(9) An assizer shall refuse to assize—
(a) an instrument of me type known as union scales; and
(b) a platform machine having counter poise weights which, when added to the full value of the steelyard reading represents a weight greater or less than the capacity of the machine - Reference of the measure
- Part IV section 27 (3&8)
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 8423.8 - Other weighing machinery : Yes Platform Machines and weighbridges - Description
- Platform Machines and weighbridges
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world 20 February 1998 - Description
- All countries
-
Applied by Zambia on the entire world for 9031.80.00: - Other instruments, appliances and machines
The measure came into effect on 20 February 1998
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 20 February 1998
- Publication where the measure is specified
- Supplement to the Republic of Zambia Government Gazette dated 20/02/1998. statutory Instrument No 22 of 1998,the weights and Measures Act
- Regulation where the measure is specified
- The weights and Measures (assize) regulations, 1998
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 41. (1) An automatic measuring instrument shall be—
(a) certify by the Superintendent Assizer in terms of section fifteen of the Act;
(b) securely fixed in position in which it will operate;
(c) tested in situ with the liquid it is intended to measure;
(d) be fitted with seals to protect all adjusting devices or have all such devices operate only with a special detachable key;
(e) marked with clear marks of identification on all parts that require to be dismantled for any purposes whatsoever, such marks to give a clear indication of the matching parts which are to be matched on re-assembly;
(f) tested at various heads and rates of delivery where these are not uniform;
(g) tested by taking not less than twenty samples either at random or in sequence; and
(h) marked with a stamp of assize upon a lead plug on conspicuous part of the instrument or on the main body of the machine.
(2) The limit of error allowed on an automatic measuring instrument shall be—
(a) the maximum error in excess or deficiency of the amount to be delivered into the container of 0.1 percent; or 0.05% in deficiency;
(b) such that the average error of a sample of twenty or more deliveries does not exceed 0.1 % in deficiency - Reference of the measure
- Part VI Section 41 (1) (e) &(h)
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 9031.80.00 - Other instruments, appliances and machines Yes Automatic Fabric Measuring Instrument - Description
- Automatic Fabric Measuring Instrument
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world 20 February 1998 - Description
- All countries
-
Applied by Zambia on the entire world for 8423.8: - Other weighing machinery : and 9016.00.00: Balances of a sensitivity of 5 cg or better, with or without weights.
The measure came into effect on 20 February 1998
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 20 February 1998
- Publication where the measure is specified
- Supplement to the Republic of Zambia Government Gazette dated 20/02/1998. statutory Instrument No 22 of 1998,the weights and Measures Act
- Regulation where the measure is specified
- The weights and Measures (assize) regulations, 1998
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 29. (1) In a spring balance—
(a) The chart shall—
(i) be clearly and indelibly marked " TRADE SPRING BALANCE " or " FOR TRADE USE ";
(ii) bear a statement of the weight "e" value; and
(iii) be made of white enamel, polished brass, or an approved material so protected that the graduation and other markings are clearly visible;
(b) the graduation on the chart shall not—
(i) exceed 0.8mm in width; and
(ii) be less than 3mm apart, measured from the centre to centre, whether or not they are on opposite sides of a dividing line;
(c) where a temperature compensating device or iso-elastic spring is incorporated, it shall be capable of compensating temperature variations of 10 degrees Celsius in balance and at load;
(d) any ball-bearing unit shall be protected against dust and dirt;
(e) the extremity of the indicating pointer shall not—
(i) exceed in width or thickness the width of any graduation; and
(ii) be more than 2min from the chart;
(f) a suitable balancing device capable of adjustment only by use of a mechanical appliance shall be provided; and
(g) be back balanced with a bag, sack, pan or other means of loading, which fact shall be clearly stated on the chart.
(3) The range of balance shall not exceed one percent of the capacity of the spring balance.
(4) A spring balance shall be tested—
(a) for accuracy of weighing at as many graduations as possible in increasing and decreasing loads;
(b) for endurance at a load equal to the capacity of the balance for a period not exceeding 24 hours and after expiration of a further four hours testing for accuracy.
(5) Subject to the provisions of regulation 15, the maximum permissible error shall be as specific in Tables 3, 5 and 6 of the First Schedule as applicable.
(6) The stamp of assize shall be stamped upon a lead plug inserted in the chart, or in a prominent position on the instrument - Reference of the measure
- Part IV section 29 (4)
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 8423.8 - Other weighing machinery : Yes Spring balance 9016.00.00 Balances of a sensitivity of 5 cg or better, with or without weights. No - Description
- Spring Balance
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world 20 February 1998 - Description
- All countries
-
Applied by Zambia on the entire world for 8423.8: - Other weighing machinery : and 9016.00.00: Balances of a sensitivity of 5 cg or better, with or without weights.
The measure came into effect on 20 February 1998
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 20 February 1998
- Publication where the measure is specified
- Supplement to the Republic of Zambia Government Gazette dated 20/02/1998. statutory Instrument No 22 of 1998,the weights and Measures Act
- Regulation where the measure is specified
- The weights and Measures (assize) regulations, 1998
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 29. (1) In a spring balance—
(a) The chart shall—
(i) be clearly and indelibly marked " TRADE SPRING BALANCE " or " FOR TRADE USE ";
(ii) bear a statement of the weight "e" value; and
(iii) be made of white enamel, polished brass, or an approved material so protected that the graduation and other markings are clearly visible;
(b) the graduation on the chart shall not—
(i) exceed 0.8mm in width; and
(ii) be less than 3mm apart, measured from the centre to centre, whether or not they are on opposite sides of a dividing line;
(c) where a temperature compensating device or iso-elastic spring is incorporated, it shall be capable of compensating temperature variations of 10 degrees Celsius in balance and at load;
(d) any ball-bearing unit shall be protected against dust and dirt;
(e) the extremity of the indicating pointer shall not—
(i) exceed in width or thickness the width of any graduation; and
(ii) be more than 2min from the chart;
(f) a suitable balancing device capable of adjustment only by use of a mechanical appliance shall be provided; and
(g) be back balanced with a bag, sack, pan or other means of loading, which fact shall be clearly stated on the chart.
(3) The range of balance shall not exceed one percent of the capacity of the spring balance.
(4) A spring balance shall be tested—
(a) for accuracy of weighing at as many graduations as possible in increasing and decreasing loads;
(b) for endurance at a load equal to the capacity of the balance for a period not exceeding 24 hours and after expiration of a further four hours testing for accuracy.
(5) Subject to the provisions of regulation 15, the maximum permissible error shall be as specific in Tables 3, 5 and 6 of the First Schedule as applicable.
(6) The stamp of assize shall be stamped upon a lead plug inserted in the chart, or in a prominent position on the instrument - Reference of the measure
- Part IV Section 29 (a)
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 8423.8 - Other weighing machinery : Yes Spring Balance 9016.00.00 Balances of a sensitivity of 5 cg or better, with or without weights. No - Description
- Spring Balance
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world 20 February 1998 - Description
- All countries
-
Applied by Zambia on the entire world for 8413.11.00: -- Pumps for dispensing fuel or lubricants, of the type used in filling-stations or in garages
The measure came into effect on 20 February 1998
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 20 February 1998
- Publication where the measure is specified
- Supplement to the Republic of Zambia Government Gazette dated 20/02/1998. statutory Instrument No 22 of 1998,the weights and Measures Act
- Regulation where the measure is specified
- The weights and Measures (assize) regulations, 1998
- Country/Region applying the measure
- Zambia
- Coded list of objectives
- X: For purposes n.e.s.
- Description of the measure
- 39. (1) A petrol pump shall—
(a) be of a pattern approved by the superintendent assizer;
(b) be constructed to deliver liquid fuel at one outlet only;
(c) be provided with a clear and legible volume indicator;
(d) not have a counting or totalising device which may be confused with volume indicator;
(e) not leak at any point;
(f) not, unless with the written permission from a superintendent assizer, be fitted with a delivery hose exceeding 5 meters
(g) when measuring the length of the delivery hose the length of the nozzle shall be included;
(ii) the length of any swing or radial arm shall be excluded; and
(iii) if it is retractable, the hose shall be measured from the point where it emerges from the housing and when fully extended;
(h) if it is of fixed type—
(i) securely mounted on a solidly constructed level base;
(ii) be so cited as to permit the purchaser to have a clear and unobstructed view of the volume indicator or measuring chamber provided;
(iii) be so cited that the adjusting mechanism and the plug for the stamp of assize are readily accessible.
(iv) if it is used to measure oil, have a delivery hose which is permanently filled to the nozzle.
(3) A petrol pump provided with a meter shall—
(a)not be capable of operation until the volume indicator and any price indicator are re-set to zero;
(b) if it is used to measure liquid fuel, may be—
(i) provided with a sight glass which clearly shows whether the delivery hose is completely filled before, during and after delivery; and
(ii) conspicuously marked " THIS GLASS MUST BE FULL BEFORE AND AFTER DELIVERY ";
(c) not to be fitted with a swing arm—
(i) which has a radius of swing not exceeding 2 meters; and
(ii) is provided with a sight glass of an approved pattern at the highest point of the swing arm or extension pipe immediately before the connection to the flexible hose;
(d) have a clear indication on the housing or dial of the position of the lead seals and the plug for the stamp of assize;
(e) be provided with an air separator or cut off valve which ensures non-registration when the supply of liquid fuel or oil fails; and
(f) be provided with a delivery hose which is permanently filled to the nozzle.
(4) A petrol pump provided with one or more measuring chambers shall—
(a) have any measuring chamber clearly visible and made of clear glass;
(b) have a delivery hose so positioned a to allow complete discharge of the liquid measured from the delivery outlet of the pump;
(c) if it has more than one measuring chamber, be provided with a valve to prevent the liquid flowing from one chamber into another; and
(d) have each measuring chamber denominated.
(5) In a petrol pump provided with a price indicator, the indicator shall incorporate a device which clearly indicates the price per litre and regulates the registration on such indicator.
(6) A petrol pump shall be tested—
(a) if it is provided with one or more measuring chambers, after passing at least 5 litres of liquid through the delivery hose to prevent undue absorption during the test;
(b) by passing the liquid into the standard measures in as many deliveries and of such quantities as the assizer considers necessary;
(c) if it is provided with a meter, by a slow test which does not exceed a time limit of thirty seconds per 5 litres on any quantity delivered;
(d) to ensure that—
(i) back drainage does not exceed 25ml per hour;
(ii) it is correct, whether the pump is operated rapidly or slowly;
(iii) the indications on the volume indicator are in agreement with those on the price indicator and with the price per litre indicated by the device referred to in sub-regulation (5), and a sufficient number of computations are checked to establish their accuracy;
(iv) if it is fitted with a nozzle control valve, no liquid fuel or oil is delivered when such valve is open and the pump is at rest;
(v) if it is fitted with two volume indicators, after delivery, it shows the same indications of volume on both such indicators; and
(vi) if it is fitted with two price indicators, after delivery it shows the same indication of value in money on both such indications.
(7) The limit of error allowed on a petrol pump shall be 0.1 percent of the quantity purported to be delivered in excess or 0.05% deficiency: Provided that in a petrol pump used to measure lubricating oil, where a quantity
of one litre or less is indicated, the limit of error allowed is 0.3 percent of the quantity purported to be delivered in excess or 0.15% deficiency.
(8) The stamp of assizer shall be stamped upon a lead plug inserted in a conspicuous and easily accessible part of the pump. A seal of assize shall be affixed where necessary to prevent access to working parts or adjusting devices without the seal being broken.
(9) In this regulation—" price indicator " means an indicator showing the value in money for the liquid fuel or oil delivered; and " volume indicator " means an indicator showing the volume of liquid fuel or oil delivery - Reference of the measure
- Part VI Section 39 (3) (ii)
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 8413.11.00 -- Pumps for dispensing fuel or lubricants, of the type used in filling-stations or in garages Yes Petrol Pump - Description
- Petrol Pump
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world 20 February 1998 - Description
- All countries
-
Applied by Zimbabwe on the entire world for 2711.1: Liquefied :
The measure came into effect on 22 February 2013
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 22 February 2013
- Publication where the measure is specified
- Statutory Instrument 23 of 2013
- Regulation where the measure is specified
- Zimbabwe Standard Specification for Liquefied Petroleum Gas
- Country/Region applying the measure
- Zimbabwe
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- The following information shall appear on each label, placard and shipping documents for products made according to this standard primary hazard class, proper shipping name substance identification number to cite a few
- Reference of the measure
- Article 5.2 p.8
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 2711.1 Liquefied : Yes lpg - Description
- Liquefied petroleum gas
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zimbabwe on the entire world for 8708.21.00: Safety seat belts
The measure came into effect on 01 September 1987
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 01 September 1987
- Publication where the measure is specified
- Statutory Instrument 147 of 1987
- Regulation where the measure is specified
- Zimbabwe Standard Specification for Restraining devices (safety Belts) for occupants of adult build in motor vehicles
- Country/Region applying the measure
- Zimbabwe
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- The belt type or type of restraint system shall be marked clearly and indelibly marked with the manufacturer's name, trade name or mark, part number, certification mark together with any other marking required in terms of the Zimbabwe Government statutory instrument.
- Reference of the measure
- Article 3.1, p. 9
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 8708.21.00 Safety seat belts No - Description
- Restraint devices (safety belts)
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zimbabwe on the entire world for 4407: Wood sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or end-jointed, of a thickness exceeding 6 mm.
The measure came into effect on 13 January 1978
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 13 January 1978
- Publication where the measure is specified
- statutory instrument 41 of 1978
- Regulation where the measure is specified
- Zimbabwe Standard specification for Sawn softwood timber: Industrial Grade
- Country/Region applying the measure
- Zimbabwe
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- The ends of each piece of timber shall be legibly and indelibly marked with manufacturer's name or trade mark, appropriate grade identification
- Reference of the measure
- Article 6.2-3, p. 8
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 4407 Wood sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or end-jointed, of a thickness exceeding 6 mm. Yes Sawn softwood timber: Industrial grade - Description
- Sawn softwood timber: Industrial grade
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zimbabwe on the entire world for 4407: Wood sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or end-jointed, of a thickness exceeding 6 mm.
The measure came into effect on 13 January 1978
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 13 January 1978
- Publication where the measure is specified
- statutory instrument 41 of 1978
- Regulation where the measure is specified
- Zimbabwe Standard Specification for Sawn softwood timber: Stress-graded Structural timber and timber for frame wall construction
- Country/Region applying the measure
- Zimbabwe
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- Each piece of stress-graded structural timber shall bear the manufacturer's name or trade mark, appropriate stress-graded identification date or batch number of the stress grading legibly and indelibly marked.
- Reference of the measure
- Article 6.2, p. 10-11
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 4407 Wood sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or end-jointed, of a thickness exceeding 6 mm. Yes Sawn softwood timber: stress-graded - Description
- Sawn softwood timber: stress-graded
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zimbabwe on the entire world for 3915.30.00: Of polymers of vinyl chloride, 3917.2: Tubes, pipes and hoses, rigid :, 3917.3: Other tubes, pipes and hoses : and 3917.40: Fittings
The measure came into effect on 13 January 1978
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 13 January 1978
- Publication where the measure is specified
- statutory instrument 41 of 1978
- Regulation where the measure is specified
- Zimbabwe Standard Specification for Unplasticised polyvinyl chloride (UPVC) Soil, waste and vent pipes and pipe fittings
- Country/Region applying the measure
- Zimbabwe
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- The manufacturer's name trade name, nominal size of the pipe, batch identification and certification mark shall appear in legible and durable marking on each pipe at intervals not exceeding 1 m and shall be applied as not to damage the pipe or to form an indentation of acceptable depth in the pipe wall
- Reference of the measure
- Article 7.2.1-2, p. 20-21
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 3915.30.00 Of polymers of vinyl chloride Yes soil and waste, unplasticised 3917.2 Tubes, pipes and hoses, rigid : Yes pipes, unplasticised pvc 3917.3 Other tubes, pipes and hoses : Yes pipes, unplasticised pvc 3917.40 Fittings Yes unplasticised pvc - Description
- Soil, waste and vent pipes and pipe fittings
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world -
Applied by Zimbabwe on the entire world for 7020.00.00: Other articles of glass
The measure came into effect on 13 January 1978
Non-Tariff Measure
- NTM classification
- B32: Marking requirements
- Date when the measure came into force
- 13 January 1978
- Publication where the measure is specified
- statutory instrument 41 of 1978
- Regulation where the measure is specified
- Zimbabwe Standard Specification for Fibreglass washdown low flush volume water-closet pans with horizontal outlets: Materials quality, performance and dimensions other than connecting dimensions
- Country/Region applying the measure
- Zimbabwe
- Coded list of objectives
- A: Protection of human life and health and E: Protection of the environment
- Description of the measure
- Water-closet pans manufactured to the requirements of this standard shall be permanently marked with manufacturer's name or identification mark
- Reference of the measure
- Article 8, p.7
- Measure also domestic
- Yes
Products affected by the measure.
Code Product Partial coverage Partial coverage indication Date in Date out 7020.00.00 Other articles of glass Yes Water closet pans of fibreglass - Description
- Water-closet pans
Countries/Regions affected by the measure.
Inclusion/Exclusion Country Date in Date out Inclusion Entire world
B32: Marking requirements
